HP printer issue instalation in Archlinux
by ruy from LinuxQuestions.org on (#585PW)
Hello, I have some problem installing my HP LaserJet CP1025nw color in Archlinux.
The steps I follow was:
1. Install CUPS, following the Arch Wiki.
Here also enable and start the service.
2. Configure the printer in CUPS.
3. Install HPLIP and HPLIP-PLUGIN
4. Install foo2zjs-nightly from git.
Here some outputs:
Code:lsusbCode:Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 046d:c077 Logitech, Inc. M105 Optical Mouse
Bus 001 Device 004: ID 04e8:6860 Samsung Electronics Co., Ltd Galaxy series, misc. (MTP mode)
Bus 001 Device 006: ID 03f0:112a HP, Inc HP LaserJet CP 1025nw
Bus 001 Device 003: ID 04f3:0103 Elan Microelectronics Corp. ActiveJet K-2024 Multimedia Keyboard
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
As show this command the printer is recognized (is connected), but when I run:
Code:sudo hp-setupThe output is:
Code:HP Linux Imaging and Printing System (ver. 3.20.6)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-18 HP Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
QStandardPaths: XDG_RUNTIME_DIR not set, defaulting to '/tmp/runtime-root'
Searching... (bus=usb, search=(None), desc=0)
error: No devices found on bus: usbAnd for the check tool of HP:
Code:sudo hp-checkThe output is:
Code:/usr/bin/hp-check:685: SyntaxWarning: "is not" with a literal. Did you mean "!="?
if 'getfacl' not in g and '' is not g and 'file' not in g:
Saving output in log file: /home/rodrigo/hp-check.log
HP Linux Imaging and Printing System (ver. 3.20.6)
Dependency/Version Check Utility ver. 15.1
Copyright (c) 2001-18 HP Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball
has the proper dependencies installed to successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode
will check both of the above cases (both compile- and run-time dependencies).
Check types:
a. EXTERNALDEP - External Dependencies
b. GENERALDEP - General Dependencies (required both at compile and run time)
c. COMPILEDEP - Compile time Dependencies
d. [All are run-time checks]
PYEXT SCANCONF QUEUES PERMISSION
Status Types:
OK
MISSING - Missing Dependency or Permission or Plug-in
INCOMPAT - Incompatible dependency-version or Plugin-version
warning: 0- version is not supported. Using 0-0 versions dependencies to verify and install...
---------------
| SYSTEM INFO |
---------------
Kernel: 5.8.8-arch1-1 #1 SMP PREEMPT Wed, 09 Sep 2020 18:59:45 +0000 GNU/Linux
Host: escritorio
Proc: 5.8.8-arch1-1 #1 SMP PREEMPT Wed, 09 Sep 2020 18:59:45 +0000 GNU/Linux
Distribution: 0
Bitness: 64 bit
-----------------------
| HPLIP CONFIGURATION |
-----------------------
HPLIP-Version: HPLIP 3.20.6
HPLIP-Home: /usr/share/hplip
warning: HPLIP-Installation: Auto installation is not supported for 0 distro version
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.20.6
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.20.6
html=/usr/share/doc/hplip-3.20.6
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
bin=/usr/bin
apparmor=/etc/apparmor.d
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
libusb01-build=no
pp-build=yes
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.20.6
restricted-build=no
ui-toolkit=qt5
qt3=no
qt4=no
qt5=yes
policy-kit=no
lite-build=no
udev_sysfs_rules=no
hpcups-only-build=no
hpijs-only-build=no
apparmor_build=no
class-driver=no
Current contents of '/var/lib/hp/hplip.state' file:
[plugin]
installed = 1
eula = 1
version = 3.20.6
Current contents of '~/.hplip/hplip.conf' file:
warning: Could not access file: No such file or directory
<Package-name> <Package-Desc> <Required/Optional> <Min-Version> <Installed-Version> <Status> <Comment>
-------------------------
| External Dependencies |
-------------------------
cups CUPS - Common Unix Printing System REQUIRED 1.1 2.3.3 OK 'CUPS Scheduler is running'
gs GhostScript - PostScript and PDF language interpreter and previewer REQUIRED 7.05 9.53.0 OK -
error: xsane xsane - Graphical scanner frontend for SANE OPTIONAL 0.9 - MISSING 'xsane needs to be installed'
error: scanimage scanimage - Shell scanning program OPTIONAL 1.0 - MISSING 'scanimage needs to be installed'
dbus DBus - Message bus system REQUIRED - 1.12.20 OK -
policykit PolicyKit - Administrative policy framework OPTIONAL - 0.117 OK -
network network -wget OPTIONAL - 1.20.3 OK -
avahi-utils avahi-utils OPTIONAL - 0.8 OK -
------------------------
| General Dependencies |
------------------------
libjpeg libjpeg - JPEG library REQUIRED - - OK -
cups-devel CUPS devel- Common Unix Printing System development files REQUIRED - 2.3.3 OK -
cups-image CUPS image - CUPS image development files REQUIRED - 2.3.3 OK -
libpthread libpthread - POSIX threads library REQUIRED - b'2.32' OK -
libusb libusb - USB library REQUIRED - 1.0 OK -
error: sane SANE - Scanning library REQUIRED - - MISSING 'sane needs to be installed'
error: sane-devel SANE - Scanning library development files REQUIRED - - MISSING 'sane-devel needs to be installed'
libnetsnmp-devel libnetsnmp-devel - SNMP networking library development files REQUIRED 5.0.9 5.8 OK -
libcrypto libcrypto - OpenSSL cryptographic library REQUIRED - 1.1.1 OK -
python3X Python 2.2 or greater - Python programming language REQUIRED 2.2 3.8.5 OK -
error: python3-notify2 Python libnotify - Python bindings for the libnotify Desktop notifications OPTIONAL - - MISSING 'python3-notify2 needs to be installed'
error: python3-pyqt4-dbus PyQt 4 DBus - DBus Support for PyQt4 OPTIONAL 4.0 - MISSING 'python3-pyqt4-dbus needs to be installed'
error: python3-pyqt4 PyQt 4- Qt interface for Python (for Qt version 4.x) REQUIRED 4.0 - MISSING 'python3-pyqt4 needs to be installed'
python3-dbus Python DBus - Python bindings for DBus REQUIRED 0.80.0 1.2.16 OK -
python3-xml Python XML libraries REQUIRED - 2.2.9 OK -
python3-devel Python devel - Python development files REQUIRED 2.2 3.8.5 OK -
python3-pil PIL - Python Imaging Library (required for commandline scanning with hp-scan) OPTIONAL - 7.2.0 OK -
error: python3-reportlab Reportlab - PDF library for Python OPTIONAL 2.0 - MISSING 'python3-reportlab needs to be installed'
--------------
| COMPILEDEP |
--------------
libtool libtool - Library building support services REQUIRED - 2.4.6 OK -
gcc gcc - GNU Project C and C++ Compiler REQUIRED - 10.2.0 OK -
make make - GNU make utility to maintain groups of programs REQUIRED 3.0 4.3 OK -
---------------------
| Python Extentions |
---------------------
cupsext CUPS-Extension REQUIRED - 3.20.6 OK -
hpmudext IO-Extension REQUIRED - 3.20.6 OK -
----------------------
| Scan Configuration |
----------------------
'/etc/sane.d/dll.conf' not found.
hpaio HPLIP-SANE-Backend REQUIRED - 3.20.6 OK 'hpaio found in /etc/sane.d/dll.conf'
error: NOT FOUND OR FAILED TO LOAD! Please reinstall HPLIP and check for the proper installation of scanext.
error: scanext Scan-SANE-Extension REQUIRED - 3.20.6 MISSING 'scanext needs to be installed'
------------------------------
| DISCOVERED SCANNER DEVICES |
------------------------------
--------------------------
| DISCOVERED USB DEVICES |
--------------------------
No devices found.
---------------------------------
| INSTALLED CUPS PRINTER QUEUES |
---------------------------------
cp1025nw
--------
Type: Unknown
Device URI: usb://HP/LaserJet%20CP%201025nw?serial=0YM51TSKPR1a
--------------
| PERMISSION |
--------------
error: Unsupported model: HP_LaserJet_CP_1025nw
-----------
| SUMMARY |
-----------
Missing Required Dependencies
-----------------------------
None
Missing Optional Dependencies
-----------------------------
None
Total Errors: 9
Total Warnings: 1
I have no idea what happen. I suppose that the issue is between the connection (I mean feedback) between the printer and the PC, but I can't fix it.
Thank you.
Ruy
The steps I follow was:
1. Install CUPS, following the Arch Wiki.
Here also enable and start the service.
2. Configure the printer in CUPS.
3. Install HPLIP and HPLIP-PLUGIN
4. Install foo2zjs-nightly from git.
Here some outputs:
Code:lsusbCode:Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 046d:c077 Logitech, Inc. M105 Optical Mouse
Bus 001 Device 004: ID 04e8:6860 Samsung Electronics Co., Ltd Galaxy series, misc. (MTP mode)
Bus 001 Device 006: ID 03f0:112a HP, Inc HP LaserJet CP 1025nw
Bus 001 Device 003: ID 04f3:0103 Elan Microelectronics Corp. ActiveJet K-2024 Multimedia Keyboard
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
As show this command the printer is recognized (is connected), but when I run:
Code:sudo hp-setupThe output is:
Code:HP Linux Imaging and Printing System (ver. 3.20.6)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-18 HP Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
QStandardPaths: XDG_RUNTIME_DIR not set, defaulting to '/tmp/runtime-root'
Searching... (bus=usb, search=(None), desc=0)
error: No devices found on bus: usbAnd for the check tool of HP:
Code:sudo hp-checkThe output is:
Code:/usr/bin/hp-check:685: SyntaxWarning: "is not" with a literal. Did you mean "!="?
if 'getfacl' not in g and '' is not g and 'file' not in g:
Saving output in log file: /home/rodrigo/hp-check.log
HP Linux Imaging and Printing System (ver. 3.20.6)
Dependency/Version Check Utility ver. 15.1
Copyright (c) 2001-18 HP Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball
has the proper dependencies installed to successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode
will check both of the above cases (both compile- and run-time dependencies).
Check types:
a. EXTERNALDEP - External Dependencies
b. GENERALDEP - General Dependencies (required both at compile and run time)
c. COMPILEDEP - Compile time Dependencies
d. [All are run-time checks]
PYEXT SCANCONF QUEUES PERMISSION
Status Types:
OK
MISSING - Missing Dependency or Permission or Plug-in
INCOMPAT - Incompatible dependency-version or Plugin-version
warning: 0- version is not supported. Using 0-0 versions dependencies to verify and install...
---------------
| SYSTEM INFO |
---------------
Kernel: 5.8.8-arch1-1 #1 SMP PREEMPT Wed, 09 Sep 2020 18:59:45 +0000 GNU/Linux
Host: escritorio
Proc: 5.8.8-arch1-1 #1 SMP PREEMPT Wed, 09 Sep 2020 18:59:45 +0000 GNU/Linux
Distribution: 0
Bitness: 64 bit
-----------------------
| HPLIP CONFIGURATION |
-----------------------
HPLIP-Version: HPLIP 3.20.6
HPLIP-Home: /usr/share/hplip
warning: HPLIP-Installation: Auto installation is not supported for 0 distro version
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.20.6
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.20.6
html=/usr/share/doc/hplip-3.20.6
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
bin=/usr/bin
apparmor=/etc/apparmor.d
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
libusb01-build=no
pp-build=yes
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.20.6
restricted-build=no
ui-toolkit=qt5
qt3=no
qt4=no
qt5=yes
policy-kit=no
lite-build=no
udev_sysfs_rules=no
hpcups-only-build=no
hpijs-only-build=no
apparmor_build=no
class-driver=no
Current contents of '/var/lib/hp/hplip.state' file:
[plugin]
installed = 1
eula = 1
version = 3.20.6
Current contents of '~/.hplip/hplip.conf' file:
warning: Could not access file: No such file or directory
<Package-name> <Package-Desc> <Required/Optional> <Min-Version> <Installed-Version> <Status> <Comment>
-------------------------
| External Dependencies |
-------------------------
cups CUPS - Common Unix Printing System REQUIRED 1.1 2.3.3 OK 'CUPS Scheduler is running'
gs GhostScript - PostScript and PDF language interpreter and previewer REQUIRED 7.05 9.53.0 OK -
error: xsane xsane - Graphical scanner frontend for SANE OPTIONAL 0.9 - MISSING 'xsane needs to be installed'
error: scanimage scanimage - Shell scanning program OPTIONAL 1.0 - MISSING 'scanimage needs to be installed'
dbus DBus - Message bus system REQUIRED - 1.12.20 OK -
policykit PolicyKit - Administrative policy framework OPTIONAL - 0.117 OK -
network network -wget OPTIONAL - 1.20.3 OK -
avahi-utils avahi-utils OPTIONAL - 0.8 OK -
------------------------
| General Dependencies |
------------------------
libjpeg libjpeg - JPEG library REQUIRED - - OK -
cups-devel CUPS devel- Common Unix Printing System development files REQUIRED - 2.3.3 OK -
cups-image CUPS image - CUPS image development files REQUIRED - 2.3.3 OK -
libpthread libpthread - POSIX threads library REQUIRED - b'2.32' OK -
libusb libusb - USB library REQUIRED - 1.0 OK -
error: sane SANE - Scanning library REQUIRED - - MISSING 'sane needs to be installed'
error: sane-devel SANE - Scanning library development files REQUIRED - - MISSING 'sane-devel needs to be installed'
libnetsnmp-devel libnetsnmp-devel - SNMP networking library development files REQUIRED 5.0.9 5.8 OK -
libcrypto libcrypto - OpenSSL cryptographic library REQUIRED - 1.1.1 OK -
python3X Python 2.2 or greater - Python programming language REQUIRED 2.2 3.8.5 OK -
error: python3-notify2 Python libnotify - Python bindings for the libnotify Desktop notifications OPTIONAL - - MISSING 'python3-notify2 needs to be installed'
error: python3-pyqt4-dbus PyQt 4 DBus - DBus Support for PyQt4 OPTIONAL 4.0 - MISSING 'python3-pyqt4-dbus needs to be installed'
error: python3-pyqt4 PyQt 4- Qt interface for Python (for Qt version 4.x) REQUIRED 4.0 - MISSING 'python3-pyqt4 needs to be installed'
python3-dbus Python DBus - Python bindings for DBus REQUIRED 0.80.0 1.2.16 OK -
python3-xml Python XML libraries REQUIRED - 2.2.9 OK -
python3-devel Python devel - Python development files REQUIRED 2.2 3.8.5 OK -
python3-pil PIL - Python Imaging Library (required for commandline scanning with hp-scan) OPTIONAL - 7.2.0 OK -
error: python3-reportlab Reportlab - PDF library for Python OPTIONAL 2.0 - MISSING 'python3-reportlab needs to be installed'
--------------
| COMPILEDEP |
--------------
libtool libtool - Library building support services REQUIRED - 2.4.6 OK -
gcc gcc - GNU Project C and C++ Compiler REQUIRED - 10.2.0 OK -
make make - GNU make utility to maintain groups of programs REQUIRED 3.0 4.3 OK -
---------------------
| Python Extentions |
---------------------
cupsext CUPS-Extension REQUIRED - 3.20.6 OK -
hpmudext IO-Extension REQUIRED - 3.20.6 OK -
----------------------
| Scan Configuration |
----------------------
'/etc/sane.d/dll.conf' not found.
hpaio HPLIP-SANE-Backend REQUIRED - 3.20.6 OK 'hpaio found in /etc/sane.d/dll.conf'
error: NOT FOUND OR FAILED TO LOAD! Please reinstall HPLIP and check for the proper installation of scanext.
error: scanext Scan-SANE-Extension REQUIRED - 3.20.6 MISSING 'scanext needs to be installed'
------------------------------
| DISCOVERED SCANNER DEVICES |
------------------------------
--------------------------
| DISCOVERED USB DEVICES |
--------------------------
No devices found.
---------------------------------
| INSTALLED CUPS PRINTER QUEUES |
---------------------------------
cp1025nw
--------
Type: Unknown
Device URI: usb://HP/LaserJet%20CP%201025nw?serial=0YM51TSKPR1a
--------------
| PERMISSION |
--------------
error: Unsupported model: HP_LaserJet_CP_1025nw
-----------
| SUMMARY |
-----------
Missing Required Dependencies
-----------------------------
None
Missing Optional Dependencies
-----------------------------
None
Total Errors: 9
Total Warnings: 1
I have no idea what happen. I suppose that the issue is between the connection (I mean feedback) between the printer and the PC, but I can't fix it.
Thank you.
Ruy