Data recovery from Gparted quited HDD
by lyub from LinuxQuestions.org on (#5JT2J)
Hello
Gparted quited while was resizing a large HDD. Can you guys figure out from the smartctl -a sdX output what is going on and best way for a beginner to intermediate Linux user to recover the data from the ntfs drive. Testdisk after deep scan thought it's not recoverable.
Really would love to get some of the data back, Thank you very much!
=== START OF INFORMATION SECTION ===
Model Family: * * HGST Deskstar NAS
Device Model: * * HGST HDN724040ALE640
LU WWN Device Id: 5 000cca 24ccf1a4b
Firmware Version: MJAOA5E0
User Capacity: * *4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: * * 512 bytes logical, 4096 bytes physical
Rotation Rate: * *7200 rpm
Form Factor: * * *3.5 inches
Device is: * * * *In smartctl database [for details use: -P show]
ATA Version is: * ATA8-ACS T13/1699-D revision 4
SATA Version is: *SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: *(0x82)Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: * * *( * 0)The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( * 24) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: * * * * * *(0x0003)Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: * * * *(0x01)Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( * 1) minutes.
Extended self-test routine
recommended polling time: ( 580) minutes.
SCT capabilities: * * * (0x003d)SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME * * * * *FLAG * * VALUE WORST THRESH TYPE * * *UPDATED *WHEN_FAILED RAW_VALUE
* 1 Raw_Read_Error_Rate * * 0x000b * 100 * 100 * 016 * *Pre-fail *Always * * * - * * * 0
* 2 Throughput_Performance *0x0005 * 136 * 136 * 054 * *Pre-fail *Offline * * *- * * * 81
* 3 Spin_Up_Time * * * * * *0x0007 * 151 * 151 * 024 * *Pre-fail *Always * * * - * * * 570 (Average 454)
* 4 Start_Stop_Count * * * *0x0012 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 367
* 5 Reallocated_Sector_Ct * 0x0033 * 100 * 100 * 005 * *Pre-fail *Always * * * - * * * 0
* 7 Seek_Error_Rate * * * * 0x000b * 100 * 100 * 067 * *Pre-fail *Always * * * - * * * 0
* 8 Seek_Time_Performance * 0x0005 * 119 * 119 * 020 * *Pre-fail *Offline * * *- * * * 35
* 9 Power_On_Hours * * * * *0x0012 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 3255
*10 Spin_Retry_Count * * * *0x0013 * 100 * 100 * 060 * *Pre-fail *Always * * * - * * * 0
*12 Power_Cycle_Count * * * 0x0032 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 168
192 Power-Off_Retract_Count 0x0032 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 417
193 Load_Cycle_Count * * * *0x0012 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 417
194 Temperature_Celsius * * 0x0002 * 122 * 122 * 000 * *Old_age * Always * * * - * * * 49 (Min/Max 0/55)
196 Reallocated_Event_Count 0x0032 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 0
197 Current_Pending_Sector *0x0022 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 0
198 Offline_Uncorrectable * 0x0008 * 100 * 100 * 000 * *Old_age * Offline * * *- * * * 0
199 UDMA_CRC_Error_Count * *0x000a * 200 * 200 * 000 * *Old_age * Always * * * - * * * 4
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 1755 hours (73 days + 3 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 80 e8 b3 a4 0b *Error: ICRC, ABRT at LBA = 0x0ba4b3e8 = 195343336
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 b0 08 b8 b3 a4 40 08 * 2d+14:21:24.761 *WRITE FPDMA QUEUED
* 61 20 00 58 80 99 40 08 * 2d+14:21:24.761 *WRITE FPDMA QUEUED
* 61 18 08 90 73 07 40 08 * 2d+14:21:24.760 *WRITE FPDMA QUEUED
* 61 10 00 50 bc 01 40 08 * 2d+14:21:24.760 *WRITE FPDMA QUEUED
* 60 08 00 58 b4 a4 40 08 * 2d+14:21:24.739 *READ FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 1121 hours (46 days + 17 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 b0 50 c3 4b 06 *Error: ICRC, ABRT at LBA = 0x064bc350 = 105628496
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 00 18 00 cf 4b 40 08 * 2d+03:28:16.704 *WRITE FPDMA QUEUED
* 61 00 10 00 c7 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
* 61 00 08 00 c3 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
* 61 70 00 c0 aa 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
* 61 38 20 d0 a6 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 1116 hours (46 days + 12 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 21 df d0 aa 04 *Error: ICRC, ABRT at LBA = 0x04aad0df = 78303455
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 00 28 00 e4 aa 40 08 * 1d+22:04:10.801 *WRITE FPDMA QUEUED
* 61 00 08 00 dc aa 40 08 * 1d+22:04:10.801 *WRITE FPDMA QUEUED
* 61 00 00 00 d5 aa 40 08 * 1d+22:04:10.800 *WRITE FPDMA QUEUED
* 61 00 20 00 e0 aa 40 08 * 1d+22:04:10.800 *WRITE FPDMA QUEUED
* 61 00 18 00 cd aa 40 08 * 1d+22:04:10.799 *WRITE FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 1013 hours (42 days + 5 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 c0 40 cb 5b 09 *Error: ICRC, ABRT at LBA = 0x095bcb40 = 157010752
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 78 a8 10 80 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 08 a0 00 78 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 10 98 08 4a 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 08 90 00 48 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 48 88 78 3a 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. *[To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
*SPAN *MIN_LBA *MAX_LBA *CURRENT_TEST_STATUS
* * 1 * * * *0 * * * *0 *Not_testing
* * 2 * * * *0 * * * *0 *Not_testing
* * 3 * * * *0 * * * *0 *Not_testing
* * 4 * * * *0 * * * *0 *Not_testing
* * 5 * * * *0 * * * *0 *Not_testing
Selective self-test flags (0x0):
* After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Gparted quited while was resizing a large HDD. Can you guys figure out from the smartctl -a sdX output what is going on and best way for a beginner to intermediate Linux user to recover the data from the ntfs drive. Testdisk after deep scan thought it's not recoverable.
Really would love to get some of the data back, Thank you very much!
=== START OF INFORMATION SECTION ===
Model Family: * * HGST Deskstar NAS
Device Model: * * HGST HDN724040ALE640
LU WWN Device Id: 5 000cca 24ccf1a4b
Firmware Version: MJAOA5E0
User Capacity: * *4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: * * 512 bytes logical, 4096 bytes physical
Rotation Rate: * *7200 rpm
Form Factor: * * *3.5 inches
Device is: * * * *In smartctl database [for details use: -P show]
ATA Version is: * ATA8-ACS T13/1699-D revision 4
SATA Version is: *SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: *(0x82)Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: * * *( * 0)The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( * 24) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: * * * * * *(0x0003)Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: * * * *(0x01)Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( * 1) minutes.
Extended self-test routine
recommended polling time: ( 580) minutes.
SCT capabilities: * * * (0x003d)SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME * * * * *FLAG * * VALUE WORST THRESH TYPE * * *UPDATED *WHEN_FAILED RAW_VALUE
* 1 Raw_Read_Error_Rate * * 0x000b * 100 * 100 * 016 * *Pre-fail *Always * * * - * * * 0
* 2 Throughput_Performance *0x0005 * 136 * 136 * 054 * *Pre-fail *Offline * * *- * * * 81
* 3 Spin_Up_Time * * * * * *0x0007 * 151 * 151 * 024 * *Pre-fail *Always * * * - * * * 570 (Average 454)
* 4 Start_Stop_Count * * * *0x0012 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 367
* 5 Reallocated_Sector_Ct * 0x0033 * 100 * 100 * 005 * *Pre-fail *Always * * * - * * * 0
* 7 Seek_Error_Rate * * * * 0x000b * 100 * 100 * 067 * *Pre-fail *Always * * * - * * * 0
* 8 Seek_Time_Performance * 0x0005 * 119 * 119 * 020 * *Pre-fail *Offline * * *- * * * 35
* 9 Power_On_Hours * * * * *0x0012 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 3255
*10 Spin_Retry_Count * * * *0x0013 * 100 * 100 * 060 * *Pre-fail *Always * * * - * * * 0
*12 Power_Cycle_Count * * * 0x0032 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 168
192 Power-Off_Retract_Count 0x0032 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 417
193 Load_Cycle_Count * * * *0x0012 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 417
194 Temperature_Celsius * * 0x0002 * 122 * 122 * 000 * *Old_age * Always * * * - * * * 49 (Min/Max 0/55)
196 Reallocated_Event_Count 0x0032 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 0
197 Current_Pending_Sector *0x0022 * 100 * 100 * 000 * *Old_age * Always * * * - * * * 0
198 Offline_Uncorrectable * 0x0008 * 100 * 100 * 000 * *Old_age * Offline * * *- * * * 0
199 UDMA_CRC_Error_Count * *0x000a * 200 * 200 * 000 * *Old_age * Always * * * - * * * 4
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 1755 hours (73 days + 3 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 80 e8 b3 a4 0b *Error: ICRC, ABRT at LBA = 0x0ba4b3e8 = 195343336
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 b0 08 b8 b3 a4 40 08 * 2d+14:21:24.761 *WRITE FPDMA QUEUED
* 61 20 00 58 80 99 40 08 * 2d+14:21:24.761 *WRITE FPDMA QUEUED
* 61 18 08 90 73 07 40 08 * 2d+14:21:24.760 *WRITE FPDMA QUEUED
* 61 10 00 50 bc 01 40 08 * 2d+14:21:24.760 *WRITE FPDMA QUEUED
* 60 08 00 58 b4 a4 40 08 * 2d+14:21:24.739 *READ FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 1121 hours (46 days + 17 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 b0 50 c3 4b 06 *Error: ICRC, ABRT at LBA = 0x064bc350 = 105628496
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 00 18 00 cf 4b 40 08 * 2d+03:28:16.704 *WRITE FPDMA QUEUED
* 61 00 10 00 c7 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
* 61 00 08 00 c3 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
* 61 70 00 c0 aa 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
* 61 38 20 d0 a6 4b 40 08 * 2d+03:28:16.702 *WRITE FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 1116 hours (46 days + 12 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 21 df d0 aa 04 *Error: ICRC, ABRT at LBA = 0x04aad0df = 78303455
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 00 28 00 e4 aa 40 08 * 1d+22:04:10.801 *WRITE FPDMA QUEUED
* 61 00 08 00 dc aa 40 08 * 1d+22:04:10.801 *WRITE FPDMA QUEUED
* 61 00 00 00 d5 aa 40 08 * 1d+22:04:10.800 *WRITE FPDMA QUEUED
* 61 00 20 00 e0 aa 40 08 * 1d+22:04:10.800 *WRITE FPDMA QUEUED
* 61 00 18 00 cd aa 40 08 * 1d+22:04:10.799 *WRITE FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 1013 hours (42 days + 5 hours)
* When the command that caused the error occurred, the device was active or idle.
* After command completion occurred, registers were:
* ER ST SC SN CL CH DH
* -- -- -- -- -- -- --
* 84 51 c0 40 cb 5b 09 *Error: ICRC, ABRT at LBA = 0x095bcb40 = 157010752
* Commands leading to the command that caused the error were:
* CR FR SC SN CL CH DH DC * Powered_Up_Time *Command/Feature_Name
* -- -- -- -- -- -- -- -- *---------------- *--------------------
* 61 78 a8 10 80 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 08 a0 00 78 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 10 98 08 4a 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 08 90 00 48 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
* 61 48 88 78 3a 5a 40 08 * * *00:01:43.351 *WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. *[To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
*SPAN *MIN_LBA *MAX_LBA *CURRENT_TEST_STATUS
* * 1 * * * *0 * * * *0 *Not_testing
* * 2 * * * *0 * * * *0 *Not_testing
* * 3 * * * *0 * * * *0 *Not_testing
* * 4 * * * *0 * * * *0 *Not_testing
* * 5 * * * *0 * * * *0 *Not_testing
Selective self-test flags (0x0):
* After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.