Buffer I/O error on dev sde, logical block 0, async page read
by dapapa from LinuxQuestions.org on (#5NE96)
Hello. I have a lenovo laptop (x1 carbon 4th gen) running luks encrypted debian. It was working fine until I replaced the battery. After rebooting the disk failed to load debian and stopped working. It was shown at bios but I could not mount it and open the partitions. I have connected the disk (m2 ssd) to another laptop with a usb adapter, in order mount the drive, decrypt the partition and recover my data, but I get the following message:
Code:[ 264.925745] scsi host8: usb-storage 2-3:1.0
[ 265.941942] scsi 8:0:0:0: Direct-Access INTEL SS DSCKKF256H6L L11P PQ: 0 ANSI: 2 CCS
[ 265.942459] sd 8:0:0:0: Attached scsi generic sg5 type 0
[ 265.942723] sd 8:0:0:0: [sde] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 265.943155] sd 8:0:0:0: [sde] Write Protect is off
[ 265.943156] sd 8:0:0:0: [sde] Mode Sense: 00 38 00 00
[ 265.943645] sd 8:0:0:0: [sde] Asking for cache data failed
[ 265.943654] sd 8:0:0:0: [sde] Assuming drive cache: write through
[ 266.045097] sd 8:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE cmd_age=0s
[ 266.045101] sd 8:0:0:0: [sde] tag#0 Sense Key : Hardware Error [current]
[ 266.045102] sd 8:0:0:0: [sde] tag#0 Add. Sense: No additional sense information
[ 266.045104] sd 8:0:0:0: [sde] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 266.045106] blk_update_request: I/O error, dev sde, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 266.045111] Buffer I/O error on dev sde, logical block 0, async page readThe output of fdisk:
Code:user@debian:~$ sudo fdisk /dev/sde
Welcome to fdisk (util-linux 2.36.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
fdisk: cannot open /dev/sde: Input/output errorThe output of smartctl:
Code:user@debian:~$ sudo smartctl -a /dev/sde
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-8-amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: INTEL SSDSCKKF256H6L
Serial Number: CVLY62550F1W256J
LU WWN Device Id: 5 5cd2e4 14d0a3805
Firmware Version: LBFL11P
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: M.2
TRIM Command: Available, deterministic
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Aug 17 08:46:23 2021 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x01) Offline data collection activity
is in a Reserved state.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 15) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 257
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0032 100 100 000 Old_age Always - 64993
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 142
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 111
170 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 64993
171 Unknown_Attribute 0x0032 076 076 010 Old_age Always - 636
172 Unknown_Attribute 0x0032 092 092 010 Old_age Always - 210
173 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 47
174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 38
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 24
184 End-to-End_Error 0x0033 000 000 097 Pre-fail Always FAILING_NOW 16777215
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 25120
190 Airflow_Temperature_Cel 0x0032 045 046 000 Old_age Always - 45 (Min/Max 38/46)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 38
194 Temperature_Celsius 0x0032 045 046 000 Old_age Always - 45 (Min/Max 38/46)
199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0
225 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 2873344
226 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 0
227 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 0
228 Power-off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
232 Available_Reservd_Space 0x0033 000 000 010 Pre-fail Always FAILING_NOW 0
233 Media_Wearout_Indicator 0x0033 093 093 001 Pre-fail Always - 0
236 Unknown_Attribute 0x0033 093 093 001 Pre-fail Always - 0
241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 2873344
242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 3526656
249 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1441825
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 140 14
# 2 Short offline Completed: read failure 90% 140 14
# 3 Short offline Completed: read failure 90% 140 14
# 4 Short offline Completed: read failure 90% 140 14
# 5 Short offline Completed: read failure 90% 140 14
# 6 Short offline Completed: read failure 90% 139 14
# 7 Short offline Completed: read failure 90% 139 14
# 8 Short offline Completed: read failure 90% 139 14
# 9 Short offline Completed: read failure 90% 139 14
#10 Short offline Completed: read failure 90% 139 14
#11 Short offline Completed: read failure 90% 139 14
#12 Short offline Completed: read failure 90% 139 14
#13 Short offline Completed: read failure 90% 139 14
#14 Short offline Completed: read failure 90% 139 14
#15 Short offline Completed: read failure 90% 138 14
#16 Short offline Completed: read failure 90% 138 14
#17 Short offline Completed: read failure 90% 138 14
#18 Short offline Completed: read failure 90% 138 14
#19 Short offline Completed: read failure 90% 138 14
#20 Short offline Completed: read failure 90% 138 14
#21 Short offline Completed: read failure 90% 137 14
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 843415614194058 4785074722897923 Not_testing
2 326229498192920576 281474976645120 Not_testing
3 843415613800842 4785079017865219 Not_testing
4 326229498192920576 281474976645120 Not_testing
5 217016197727584650 4785079017865217 Not_testing
2987 77309411487 77309477022 Read_scanning is in a Reserved state
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 65535 minute delay.Anyone have any idea what to do now? Thanks in advance.
Code:[ 264.925745] scsi host8: usb-storage 2-3:1.0
[ 265.941942] scsi 8:0:0:0: Direct-Access INTEL SS DSCKKF256H6L L11P PQ: 0 ANSI: 2 CCS
[ 265.942459] sd 8:0:0:0: Attached scsi generic sg5 type 0
[ 265.942723] sd 8:0:0:0: [sde] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 265.943155] sd 8:0:0:0: [sde] Write Protect is off
[ 265.943156] sd 8:0:0:0: [sde] Mode Sense: 00 38 00 00
[ 265.943645] sd 8:0:0:0: [sde] Asking for cache data failed
[ 265.943654] sd 8:0:0:0: [sde] Assuming drive cache: write through
[ 266.045097] sd 8:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE cmd_age=0s
[ 266.045101] sd 8:0:0:0: [sde] tag#0 Sense Key : Hardware Error [current]
[ 266.045102] sd 8:0:0:0: [sde] tag#0 Add. Sense: No additional sense information
[ 266.045104] sd 8:0:0:0: [sde] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 266.045106] blk_update_request: I/O error, dev sde, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 266.045111] Buffer I/O error on dev sde, logical block 0, async page readThe output of fdisk:
Code:user@debian:~$ sudo fdisk /dev/sde
Welcome to fdisk (util-linux 2.36.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
fdisk: cannot open /dev/sde: Input/output errorThe output of smartctl:
Code:user@debian:~$ sudo smartctl -a /dev/sde
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-8-amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: INTEL SSDSCKKF256H6L
Serial Number: CVLY62550F1W256J
LU WWN Device Id: 5 5cd2e4 14d0a3805
Firmware Version: LBFL11P
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: M.2
TRIM Command: Available, deterministic
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Aug 17 08:46:23 2021 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x01) Offline data collection activity
is in a Reserved state.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 15) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 257
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0032 100 100 000 Old_age Always - 64993
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 142
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 111
170 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 64993
171 Unknown_Attribute 0x0032 076 076 010 Old_age Always - 636
172 Unknown_Attribute 0x0032 092 092 010 Old_age Always - 210
173 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 47
174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 38
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 24
184 End-to-End_Error 0x0033 000 000 097 Pre-fail Always FAILING_NOW 16777215
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 25120
190 Airflow_Temperature_Cel 0x0032 045 046 000 Old_age Always - 45 (Min/Max 38/46)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 38
194 Temperature_Celsius 0x0032 045 046 000 Old_age Always - 45 (Min/Max 38/46)
199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0
225 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 2873344
226 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 0
227 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 0
228 Power-off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
232 Available_Reservd_Space 0x0033 000 000 010 Pre-fail Always FAILING_NOW 0
233 Media_Wearout_Indicator 0x0033 093 093 001 Pre-fail Always - 0
236 Unknown_Attribute 0x0033 093 093 001 Pre-fail Always - 0
241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 2873344
242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 3526656
249 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1441825
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 140 14
# 2 Short offline Completed: read failure 90% 140 14
# 3 Short offline Completed: read failure 90% 140 14
# 4 Short offline Completed: read failure 90% 140 14
# 5 Short offline Completed: read failure 90% 140 14
# 6 Short offline Completed: read failure 90% 139 14
# 7 Short offline Completed: read failure 90% 139 14
# 8 Short offline Completed: read failure 90% 139 14
# 9 Short offline Completed: read failure 90% 139 14
#10 Short offline Completed: read failure 90% 139 14
#11 Short offline Completed: read failure 90% 139 14
#12 Short offline Completed: read failure 90% 139 14
#13 Short offline Completed: read failure 90% 139 14
#14 Short offline Completed: read failure 90% 139 14
#15 Short offline Completed: read failure 90% 138 14
#16 Short offline Completed: read failure 90% 138 14
#17 Short offline Completed: read failure 90% 138 14
#18 Short offline Completed: read failure 90% 138 14
#19 Short offline Completed: read failure 90% 138 14
#20 Short offline Completed: read failure 90% 138 14
#21 Short offline Completed: read failure 90% 137 14
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 843415614194058 4785074722897923 Not_testing
2 326229498192920576 281474976645120 Not_testing
3 843415613800842 4785079017865219 Not_testing
4 326229498192920576 281474976645120 Not_testing
5 217016197727584650 4785079017865217 Not_testing
2987 77309411487 77309477022 Read_scanning is in a Reserved state
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 65535 minute delay.Anyone have any idea what to do now? Thanks in advance.