Uncompressing Linux... done, booting the kernel. (Beaglebone Black, Angstrom)
by Lesterlop from LinuxQuestions.org on (#5PX9C)
Hello everyone,
I'm new to Beaglebone Black, I'm following a course on-line but I'm struggling with rootfs. I've done the two partitions (SD card), in the BOOT partition I have ran the MLO without no problem, then I have ran the MLO and the u-image.img and it boots just fine. The problem seems to be in the rootfs partition, I installed the rootfs https://drive.google.com/drive/folde...YZ6Of6L_MBSEZD recommended by the instructor but it hangs here Uncompressing Linux... done, booting the kernel. I'm using the 5V DC 2A Wall adapter.
These are the logs that I'm getting
U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
372 bytes read in 3 ms (121.1 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
4002080 bytes read in 699 ms (5.5 MiB/s)
23334 bytes read in 19 ms (1.2 MiB/s)
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/3.8.10/beaglebone
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4002016 Bytes = 3.8 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 88000000
Booting using the fdt blob at 0x88000000
Loading Kernel Image ... OK
OK
Using Device Tree in place at 88000000, end 88008b25
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
If any of you have experienced this problem with the same device please, do let me know what to do. Thanks in advance.
I'm new to Beaglebone Black, I'm following a course on-line but I'm struggling with rootfs. I've done the two partitions (SD card), in the BOOT partition I have ran the MLO without no problem, then I have ran the MLO and the u-image.img and it boots just fine. The problem seems to be in the rootfs partition, I installed the rootfs https://drive.google.com/drive/folde...YZ6Of6L_MBSEZD recommended by the instructor but it hangs here Uncompressing Linux... done, booting the kernel. I'm using the 5V DC 2A Wall adapter.
These are the logs that I'm getting
U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
372 bytes read in 3 ms (121.1 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
4002080 bytes read in 699 ms (5.5 MiB/s)
23334 bytes read in 19 ms (1.2 MiB/s)
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/3.8.10/beaglebone
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4002016 Bytes = 3.8 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 88000000
Booting using the fdt blob at 0x88000000
Loading Kernel Image ... OK
OK
Using Device Tree in place at 88000000, end 88008b25
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
If any of you have experienced this problem with the same device please, do let me know what to do. Thanks in advance.